Shootbolt home

HOPPE repair helpby Shootbolt

Multipoint door adjustment

How to adjust a multipoint lock: line up the door, not the lock.

Works with the door open, but not shut? The lock is fine. The door has moved, and its bolts are missing their strike plates.

How do you adjust a multipoint lock?

You adjust the door around the lock. Test the lock with the door open. If it works, find where the bolts miss, tighten or adjust the hinges, and move the strike plates last.

The door-open test

Open the door and press in the small spring plunger beside the latch. Lift the handle all the way and turn the key or thumbturn. Turn it back and push the handle down before you close the door.

Easy open, hard or impossible shut: the door is out of line. Adjust it, using the steps below.
Stiff, clicking or slack even with the door open: the lock itself is worn. See what each handle problem means.

A new lock case will not fix a door that is out of line. Don't force the handle: on a misaligned door, that strains the lock case.

Handle won't lift or key won't turn with the door shut? Why a door won't lock when it's closed.

Find where it misses: the tape test

Put masking tape over every strike plate in the frame, not just the one by the handle. Close the door slowly until the bolts touch the tape, then open it and read the marks.

What you findWhat it meansFix
Every mark is low by the same amount; the gap above the door is wider at the latch endThe door has saggedThe hinges, not each strike
One mark is off; the gaps around the door are evenThat one strike is out of lineMove or file that strike
The latch catches, but the door rattlesThe strike sits too far from the door stopBend the tab or move the strike in

Fix the hinges first

A sagging door throws off every bolt at once, so a strike moved first has to be moved again. Make one change at a time, and lock the door shut after each.

  1. Tighten every hinge screw by hand

    Door side and frame side, top hinge first. A power driver strips the holes.

  2. Drive one long screw into the wall framing

    On plain hinges, stock screws reach only the thin frame board. Follow your door maker first: Therma-Tru's manual puts #10 x 2-1/2" (64 mm) screws in the two top-hinge holes nearest the weatherstrip, in 1/8" (3 mm) pilot holes. With no maker rule, a 3" (76 mm) screw is common. Snug it; overdriving pulls the frame out of line.

  3. Or turn the adjustable hinges

    Many multipoint doors have hex-key hinges. HOPPE adjustable hinges take a 3/16" (4.8 mm) hex and move about 1/8" (3 mm) each way. Never knock out the hinge pin. Turn by hand, a quarter turn at a time, and watch the gap: screw directions differ between brands.

  4. Shim the bottom hinge if the gaps are still uneven

    A strip of cardboard or a plastic hinge shim, about 1/16" (1.6 mm) to start, behind the bottom hinge's frame leaf lifts the latch side of a sagging door.

Then adjust the strike plates

Once the gaps are even, move only a strike that still misses, and retest with fresh tape. These are rules of thumb, not maker specs.

The bolt misses byFix
1/32" to 1/16" (0.8 to 1.6 mm)Loosen the strike screws, nudge it toward the mark, retighten
Up to 1/8" (3 mm)File the edge of the opening the bolt is hitting
More than 1/8" (3 mm)Move the strike: re-cut its recess and drill new screw holes
  • Rollers: on HOPPE locks with rollers, each roller has an off-center cam. A 5/32" (4 mm) hex key moves it about 1/32" (1 mm) either way.
  • The latch slams in flat side first: the latch is in backwards. On an HLS 9000, pull it out, turn it half a turn and let it spring back.
  • The bottom bolt stops short: vacuum the grit out of the hole in the sill.

French doors: bolt the second door first

The main (active) door locks into the strip on the second (inactive) door's edge, the astragal. So the second door has to be solid first.

  1. Bolt the second door top and bottom

    Slide the top flush bolt up and the bottom one down, fully, or lift its handle if it has one. If the door moves when you push it, a bolt isn't in. Some locks, such as HOPPE's HLS 7, won't let the main door lock until the second door is locked.

  2. Check the bolts reach

    HOPPE second-door shootbolts throw 3/4" (20 mm) or 1" (25 mm), so there is little to spare. Dirt in the sill hole, or a dropped door, can stop them.

  3. Look down the seam

    If one door has sagged, the seam between the doors narrows at the top, and the main door's latch lands low on the astragal. Find the door that dropped and fix its hinges.

  4. Then test the main door open

    Locks open but not shut? A strike on the astragal, or the door, is out of line.

Questions

How do I adjust a multipoint lock?

Test it with the door open. If it works, tape the strikes to see where the bolts miss, fix the hinges, then move any strike that still misses. Stiff even with the door open means the lock itself is worn.

How do I fix a door latch that doesn't line up?

Put masking tape on the strike and close the door gently. A mark below the hole with a wider gap above the latch end means sag: tighten the hinge screws first. With even gaps, nudge or file the strike toward the mark.

What are the possible reasons why my French door won't latch?

The second door isn't bolted at the top and bottom, a flush bolt is blocked by dirt in the sill hole, one door has sagged so the latch lands low on the astragal, or the astragal's weatherstrip is caught behind the head weatherstrip and the door won't close fully. A racked frame needs a carpenter.

Will a new lock case fix a door that won't lock?

Not if the door is out of line. If it locks easily with the door open, adjust first: a new case on the same door would bind the same way. Stiff or broken even when open? See lock case or whole lock.

When should I call someone?

Call a carpenter or the installer if the frame is out of square, the wood is split or rotted, or the hinges have no adjustment left. A new door may be under warranty: ask its maker first. If the door is locked shut, see door stuck locked and don't drill the lock. If anyone is locked in or in danger, call 911.

Still stiff with the door open? Tell the problems apart; a worn lock case is a one-part fix. Not sure? Use the instant part identifier, or send us a photo of the door's edge. We reply by email within 1 business day.

If adjusting does not fix it, see how to replace just the gearbox.

HOPPE HLS 9000 lock case with latch and deadbolt

The part

HOPPE HLS 9000 replacement lock case

  • Genuine HOPPE part, in six sizes
  • Choose your size for price and availability
  • Free US shipping and 90-day free returns
Choose my size You pay on shootbolt.com, our store.
HOPPE HLS 9000 gearboxFree US shipping · 90-day returnsView sizes
Choose size