Shootbolt home

HOPPE repair helpby Shootbolt

Replacing a HOPPE HLS 9000 lock case

How to replace a HOPPE HLS 9000 gearbox (lock case).

Ten steps, the tools to have ready, and one rule: the door stays open until every locking point has been tested.

Have these ready

#3 tri-wing bit and hand bit holderFor the screws that join the case to the extensions. Most toolboxes don't have one, so get it before you start.
3 mm hex keyFor the small set screw under each lever.
Phillips screwdriverA hand screwdriver, not a power driver. The lock is fitted hand-tight.
A table or a clear floorThe lock comes out of the door in one long piece. You need room to lay it down.

Don't own a 3 mm hex key? You can add HOPPE's 3 mm hex wrench to a lock case order. A new cylinder retaining screw, matched to your backset, is offered there too.

Take the old lock out

  1. Unlock and open the door

    Turn the key or thumbturn back first, then push the handle down. Prop the door open. It stays open until the last step.

  2. Take out the key cylinder

    Remove the long screw in the door's edge, level with the cylinder. Turn the key a little until the cylinder slides free, and pull it out.

  3. Take off the handles

    Loosen the set screw under each lever with the 3 mm hex key. Remove the screws in the inside plate, lift both plates off and pull out the square spindle.

  4. Remove the lock from the door's edge

    Take out the screws along the faceplate strip and ease the whole lock out of the door. Lay it flat.

Swap the case

  1. Compare old and new

    Lay the new case beside the old one with the handle holes lined up. The backset, the deadbolt and the 3-5/8" (92 mm) handle spacing should agree. If they don't, stop here: a part that doesn't match goes back free within 90 days.

  2. Disconnect the old case

    Undo the screws that join the case to the extensions. These are the ones that take the #3 tri-wing bit. Leave the case itself closed: HOPPE doesn't sell the parts inside.

  3. Fit the new case

    Attach the lower extension to the new case, then the upper.

  4. Check the latch faces the right way

    The sloped face of the latch should meet the strike as the door closes, the same way as on the old case. The latch is reversible: pull it out, turn it half a turn and let it spring back.

Refit and test

  1. Refit with a few screws, and test with the door open

    Slide the lock back into the door's edge and put in a few screws. Press in the small spring plunger beside the latch, lift the handle and turn the thumbturn. Every locking point should move freely. Turn the thumbturn back and push the handle down: every bolt should go back in.

  2. Finish, and test again

    Fit the rest of the screws, snug by hand with the heads flush. Refit the spindle, the handles, the cylinder and its screw. Test every locking point once more with the door open. Only then close the door and lock it.

Why hand-tight?

Therma-Tru's installation guide for this lock warns that too much force on the screws makes the lock bind. Snug is enough.

If something isn't right

It binds with the door open

Don't close the door. Check that the case and the extensions are fully joined, that no screw is overtightened, and that the latch faces the right way.

It works open, but it is stiff with the door shut

Door alignment or interference at the strike plates may be causing the binding. That is hard on a new case too, so look at the strike plates and hinges now.

The handle still droops

Look for a handle shaft rubbing in its hole, and try the bare spindle test on the handle problems page. A spindle that returns on its own points toward the handle or friction, but it does not diagnose every possible fault. Contact us if you are unsure.

You would sooner not do it yourself

Call a locksmith or a door installer, and ask first whether they work on multipoint locks. In our 2026 study of 9,443 U.S. locksmith websites, 283 (3.0%) said they do. How to find one and what to ask, on shootbolt.com.

When to stop and call someone

If the door is new, ask the door maker first: the lock may be under warranty. Call a locksmith or door installer if the door is locked shut, won't lock at all, or nothing you measure matches a size. If anyone is locked in or in danger, call 911.

What a buyer said about the job

★★★★★
"Shipping was free and fast - arrived in just 2 days! The lock was clean, securely packaged, and easy to remove from the faceplate and swap out for my customer."
Justin Ross, locksmith · November 17, 2026

One of 2 reviews on shootbolt.com, both 5 stars. We only publish reviews from verified buyers.

Before you start, print the one-page repair checklist. Still need the part? Order the HOPPE gearbox.

HOPPE HLS 9000 lock case with latch and deadbolt

The part

HOPPE HLS 9000 replacement lock case

  • Genuine HOPPE part, in six sizes
  • Choose your size for price and availability
  • Free US shipping and 90-day free returns
Choose my size You pay on shootbolt.com, our store.
HOPPE HLS 9000 gearboxFree US shipping · 90-day returnsView sizes
Choose size