Shootbolt home

HOPPE repair helpby Shootbolt

Measuring for a HOPPE HLS 9000 lock case

Two measurements choose your size. Here is where to put the tape.

First confirm your lock family. Then match these two measurements to choose the size; do not choose by appearance alone.

Before you measure

  • Open the door. Every measurement is taken at the door's edge.
  • Get the deadbolt out. Press in the small spring plunger beside the latch, lift the lever, then turn the thumbturn. Turn it back and push the lever down before you close the door again.
  • Read millimeters if your tape has them. These locks are made in metric sizes, so the millimeter reading is the easy one to match.
  1. Backset

    Measure from the face of the faceplate (the metal strip in the door's edge) to the center of the handle hole.

    You should get 1-3/8" (35 mm), 1-3/4" (45 mm), 2-3/8" (60 mm) or 2-3/4" (70 mm).

A HOPPE lock case with an arrow from the faceplate to the center of the square handle hole, labeled backset
Backset: faceplate to the center of the square handle hole. Shown on a lock out of the door; on your door, measure between the same two points.
  1. Deadbolt throw

    With the deadbolt fully out, measure how far it sticks out past the faceplate.

    You should get 9/16" (14 mm) or 1" (25.4 mm).

A HOPPE deadbolt fully extended, with an arrow from the faceplate to the end of the bolt, labeled throw
Throw: from the faceplate to the end of the fully extended deadbolt.
  1. Handle spacing, to confirm

    Measure from the center of the handle hole to the center of the key cylinder hole.

    You should get 3-5/8" (92 mm), always. This one doesn't choose a size. It confirms you have the right lock.

A HOPPE lock case with an arrow from the center of the square handle hole to the center of the key cylinder hole, labeled PZ
Handle spacing, center to center. The trade calls it PZ.

The six sizes

Find your backset in the first column, then your throw.

Backset9/16" (14 mm) throw1" (25.4 mm) throw
1-3/8" (35 mm)✓ Yes✓ Yes
1-3/4" (45 mm)✓ Yes✓ Yes
2-3/8" (60 mm)Not offered✓ Yes
2-3/4" (70 mm)Not offered✓ Yes

Seen a gearbox listed as 45/92/25? Sellers write backset/handle spacing/throw in millimeters. 45/92/25 is a 1-3/4" (45 mm) backset, 3-5/8" (92 mm) handle spacing and a 1" (25.4 mm) throw.

I have my measurements 90-day free returns · prepaid return label, no restocking fee

Three things that trip people up

Measuring a case that is out of the door

Use the faceplate as your reference. A bare case has no faceplate and can read about 2 mm short, so a case that measures about 43 mm on the bench is a 45 mm backset.

Worrying about the faceplate width

You don't need it for this part. One case suits both faceplate widths, 5/8" (16 mm) and 3/4" (20 mm), because your own faceplate goes back on.

Measuring from the edge of the door

Measure from the metal faceplate, not from the wood or the weatherstrip beside it.

Your numbers don't match a size?

Don't pick the nearest one. Send us a photo of the door's edge with your measurements, and we reply by email within 1 business day. You can also check that the lock is a HOPPE HLS 9000.

With both numbers written down, pick your HOPPE gearbox size, and print the repair checklist for the day of the job.

HOPPE HLS 9000 lock case with latch and deadbolt

The part

HOPPE HLS 9000 replacement lock case

  • Genuine HOPPE part, in six sizes
  • Choose your size for price and availability
  • Free US shipping and 90-day free returns
Choose my size You pay on shootbolt.com, our store.
HOPPE HLS 9000 gearboxFree US shipping · 90-day returnsView sizes
Choose size